| <back> |
Floor Saw Blades for Asphalt
| |
Part.-No. |
Segments
Dimensions in mm |
Nominal Diameter |
| A350: wide gullet -for floor saws up to 20 KW (quick cutting) | | 952730 | 40x3,2x7,0 | 300 | | 952731 | 40x3,2x7,0 | 350 | | 952732 | 40x3,2x7,0 | 400 | | 952733 | 40x3,6x7,0 | 450 | | 952734 | 40x3,6x7,0 | 500 | | 952735 | 40x3,6x7,0 | 600 | | 952736 | 40x5,0x7,0 | 600 | | 952737 | 40x4,7x7,0 | 700 | | 952738 | 40x4,7x7,0 | 800 | | 952739 | 40x4,7x7,0 | 900 | | 952740 | 40x4,7x7,0 | 1000 | |
| A351: wide gullet - for floor saws over 20 KW (long life time) | | 952770 | 40x3,2x9,0 | 300 | | 952771 | 40x3,2x9,0 | 350 | | 952772 | 40x3,2x9,0 | 400 | | 952773 | 40x3,6x9,0 | 450 | | 952774 | 40x3,6x9,0 | 500 | | 952775 | 40x3,6x9,0 | 600 | | 952776 | 40x5,0x9,0 | 600 | | 952777 | 40x4,7x9,0 | 700 | | 952778 | 40x4,7x9,0 | 800 | | 952779 | 40x4,7x9,0 | 900 | | 952780 | 40x4,7x9,0 | 1000 | | 
| A360: normal gullet quick cutting | | 952720 | 40x3,2x7,0 | 300 | | 952721 | 40x3,2x7,0 | 350 | | 952722 | 40x3,2x7,0 | 400 | | 952723 | 40x3,6x7,0 | 450 | | 952724 | 40x3,6x7,0 | 500 | | 952725 | 40x3,6x7,0 | 600 | | 952726 | 40x5,0x7,0 | 600 | | 952727 | 40x4,7x7,0 | 700 | | 952728 | 40x4,7x7,0 | 800 | | 952729 | 40x4,7x7,0 | 900 | | 952760 | 40x4,7x7,0 | 1000 | |
| A361: normal gullet long life time | | 952750 | 40x3,2x9,0 | 300 | | 952751 | 40x3,2x9,0 | 350 | | 952752 | 40x3,2x9,0 | 400 | | 952753 | 40x3,6x9,0 | 450 | | 952754 | 40x3,6x9,0 | 500 | | 952755 | 40x3,6x9,0 | 600 | | 952756 | 40x5,0x9,0 | 600 | | 952757 | 40x4,7x9,0 | 700 | | 952758 | 40x4,7x9,0 | 800 | | 952759 | 40x4,7x9,0 | 900 | | - | 40x4,7x9,0 | 1000 | | 
| A355: short gullet - for floor saws over 20 KW, quick cutting, very long life time | | 950650 | 40x3,2x9,0 | 300 | | 950651 | 40x3,2x9,0 | 350 | | 950652 | 40x3,2x9,0 | 400 | | 950653 | 40x3,6x9,0 | 450 | | 950654 | 40x3,6x9,0 | 500 | | 950655 | 40x3,6x9,0 | 600 | | 950656 | 40x5,0x9,0 | 600 | | 950657 | 40x4,7x9,0 | 700 | | 950658 | 40x4,7x9,0 | 800 | | 950659 | 40x4,7x9,0 | 900 |
| For optimal sawing results a periheral speed of 45 - 60 m/sec is recommended. Cutting in loose ground will cause early segment wear and segment loss by demaging steel centre. |
Diamond Floor Saw Blades - Green concrete
| |
Part.-Nr. |
Segments
Dimensions in mm |
Nominal Diameter |
| C320: short gullet - for cured concrete with less abrasivity | | 952620 | 40x3,2x9,0 | 300 | | 952621 | 40x3,8x9,0 | 300 | | 952623 | 40x3,2x9,0 | 350 | | 952624 | 40x3,8x9,0 | 350 | C330: for green concrete with higher abrasivity , quarz and industrial floors. | | 952630 | 40x3,2x9,0 | 300 | | 952631 | 40x3,8x9,0 | 300 | | 952633 | 40x3,2x9,0 | 350 | | 952634 | 40x3,8x9,0 | 350 |
| For optimal sawing results, a peripheral speed of 45-60 m/s is recommended. |
| |
